
ОПИСАНИЕ НА РУССКОМ 

ЧТО НОВОГО:
-Для бесконтактных датчиков добавлена возможность выбора парметров калибровки и запуска калибровки из самой программы.
 Процедура калибровки с троекратным включением и отключением питания при удаленном от магнита датчике так же работает,
 но из программы это делать проще - ненужно снимать датчик и удалять от магнита. 
 Если вы приобрели конвертер до 24.02.2026 и он уже  откалиброван и стоит на авто, то особого смысла в обновлении нет.
 Просто используйте новую настроечную программу, она с ним полностью совметима. 
 Но если все же хочется обновить, то читайте далее :) 


ИНСТРУКЦИЯ ПО ОБНОВЛЕНИЮ ПРОШИВКИ
В этой папке расположены прошивки для версии конвертера именно  с бесконтактным датчиком. 
ПРОШИВКИ ИЗ ЭТОЙ ПАПКИ НЕЛЗЯ ЗАЛИВАТЬ В КОНВЕРТЕРЫ ВЕРСИИ BT-PRO.

Конвертеры  с  бесконтактным датчиком собирались на платах с кварцем( версия 16MHZ) и без него (версия 8MHZ).
Внимательно посмотрите фотографии в этой папке и сравните со своей платой , чтобы выбрать правильную прошивку. 

Прошивка заливается прямо из настроечной программы.
Для этого нужно подключиться к конвертеру, затем перейти  на вкладку "настройки", выбрать файл прошивки  и дождаться обновления прошивки.
После обновления , необходимо запустить панель приборов и убедиться , что все работает. 

Если  в процессе обновления что-то пошло не так , или вы по ошибке залили  не ту прошивку и конвертер перестал выходить на связь, 
то восстановление прошивки необходимо делать по этой инструкции
https://youtu.be/i7v-9MfCCTI


ENGLISH DESCRITPION

WHAT’S NEW:
-For contactless sensors, the ability to select calibration parameters and start calibration directly from the software has been added.
 The calibration procedure using three power on/off cycles with the sensor positioned away from the magnet still works,
 but doing it from the software is much easier — there is no need to remove the sensor or move it away from the magnet.
 If you purchased the converter before 24.02.2026 and it has already been calibrated and installed in the vehicle, there is no particular need to update it.
 Simply use the new configuration software — it is fully compatible with your device.
 However, if you still want to update, read on :)

FIRMWARE UPDATE INSTRUCTIONS
This folder contains firmware specifically for the converter version with a contactless sensor.
Firmware from this folder must NOT be uploaded to BT-PRO version converters.

Converters with a contactless sensor were assembled on boards with a crystal oscillator (16 MHz version) and without it (8 MHz version).
Carefully review the photos in this folder and compare them with your board to select the correct firmware.

The firmware is uploaded directly from the configuration program.
To do this, connect to the converter, then go to the “Settings” tab, select the firmware file, and wait for the update to complete.

After the update, you need to launch the dashboard and make sure everything is working properly.

If something goes wrong during the update process, or if you accidentally upload the wrong firmware and the converter stops responding,
the firmware recovery must be performed according to this instruction:
https://youtu.be/i7v-9MfCCTI

